LM2940CT-5 DATASHEET PDF

LMCT/NOPB Texas Instruments LDO Voltage Regulators 1A LDO REG datasheet, inventory, & pricing. 1A LDO REG. Datasheet: . Documents (5). Low drop-out voltage regulator. Order code. Manufacturer code. Description. LMCT LMCT-5 1A REGULATOR (RC). LMCT-5 -. The LM/LMC positive voltage regulator features the ability to source 1A of output current with a dropout voltage of typically V and a .

Author: Kagagul Shaktikasa
Country: Anguilla
Language: English (Spanish)
Genre: Literature
Published (Last): 26 February 2015
Pages: 382
PDF File Size: 9.23 Mb
ePub File Size: 18.4 Mb
ISBN: 460-4-37130-646-7
Downloads: 28154
Price: Free* [*Free Regsitration Required]
Uploader: Vojinn

Quick Links Categories Recent Discussions. The only things being powered in the circuit dxtasheet the stamp and the LCD. The LM gets hot after a few min which isn’t nice.

LM2940CT-5 PDF Datasheet浏览和下载

The burn your finger kind of hot. I have a 22uf cap between the output and ground as specified in the datasheet for stability. Is ths just because of the load placed on it due to the lcd?

Should I use some other voltage regulator? Datzsheet 10 Comments sorted by Date Added Votes. Hi John, What is the input voltage to the regulator — can you measure it?

The power in Watts being dissipated within the regulator is the voltage drop across the regulator times the current passing through it. Do you know about how much output current you have?

LMCT-5 Datasheet

Typically, LCD displays take very little, but I’m not familiar with the unit you’re using. Does it have a backlight? There is another possibility Did you take steps to obtain caps with appropriate ESR?

  CANTOS POPULARES DE MI TIERRA CANDELARIO OBESO PDF

I haven’t experienced it personally, but you could have an issue there that might result in overheating. Here’s a snip from p.

Larger values of output capacitance will give improved transient response. The ESR of the output capacitor will cause loop instability if it is too high or too low. The acceptable range of ESR plotted versus load current is shown in the graph datashest.

It is essential that the output capacitor meet these requirements, or oscillations can result.

If you aren’t running very much current, and your Vin isn’t too high, a small clip-on heat sink can significantly reduce the regulator’s temperature. Hello, All I have is a cap between the output and ground at 22uf.

What are the caps on the BS2P40 demo board? I can’t find a schematic of it.

LMCT-5 (ETC) PDF技术资料下载 LMCT-5 供应信息 IC Datasheet 数据表 (6/17 页)

datasheef That would work alright. It’s interesting that mine gets this hot when I have seen schematics using the same setup, with a 10uf cap even. My input is 9V, I’m using the power supply that came with the P40 demo board.

I believe the data sheets show a 0. Keep in mind the adapter you have may be putting out more than 9 volts, or may not have a very clean output, both of which will make the regulator get hot.

  ATHANAIKKUM AASAIPADU PDF

Also, remember the more voltage you have to drop and the more current you want to pull, the hotter the device will run. Another data sheet says 0. Check your caps, it might be leaky. Another, does your LCD has backlights? Photos – easier uploading and sharing. Thank you for all the input. I will try it with the additional cap.

LM2940ct 5.0 gets HOT quick.

Thanks, John In basicstamps yahoogroups. Many of the regulators require capacitance on the input and output to minimize oscillation. Furthermore, hidden in the ap note the ones that I have seen is an admonition to have a minimum current load. Otherwise the output impedance is too high and it oscillates.

I like to put a led on the output for the minimum load, and to show, solidly, that power IS really on. Friday, December 05, Basic Stamp List Datasheett Text in the Subject and Body of the message will be ignored. Your use of Yahoo! Groups is subject to http: Sign In or Register to comment.